LORA WIFI RF Arduino Shield, ESP8266 SX1278 - ElectroDragon
Par un écrivain mystérieux
Last updated 02 juin 2024
This arduino shield combine the wifi mcu module esp-12f and lora sub-1G RF module. ESP8266 ESP-12F Features: ESP-12F serial to Arduino serial, selectable D0 / D1 or soft serial D2 / D3 All pins lead out, is not connected nor occupy by Arduino IO port ESP-12F can work as slave mode for arduino, or program […]
This arduino shield combine the wifi mcu module esp-12f and lora sub-1G RF module. ESP8266 ESP-12F Features: ESP-12F serial to Arduino serial, selectable D0 / D1 or soft serial D2 / D3 All pins lead out, is not connected nor occupy by Arduino IO port ESP-12F can work as slave mode for arduino, or program independently. ADC and ADC external voltage port lead out. On board PROG programmable button, and ESP reset button. Demo code inlcudes manipulating AT commands to transiceive data from web, find in the wiki documentaion link below. Can be used independently, can be connected to a standard serial communication FTDI Lora Module SX1278/76: Reserved but not place module. D10 default used for lora chip select pin. D5-D7 can connect via jumper to D1, D2, D5 lora DIO pins. D2 default used for lora IRQ DIO0 pin. Antenna not connected default, support pin, ipex, or sma type connector, suit your needs. All lead out DIO D0 ~ D5 pins on side. Addon: Extra DH11 socket, with 10K pull-up data pin. Packaging: Only include the main board with esp-12F as red board. Not include any pin headers, lora module, antenna. Arduino pin header please buy alone here. the last image of the green board indicates the final soldered state only. Documentation please see on this page.
This arduino shield combine the wifi mcu module esp-12f and lora sub-1G RF module. ESP8266 ESP-12F Features: ESP-12F serial to Arduino serial, selectable D0 / D1 or soft serial D2 / D3 All pins lead out, is not connected nor occupy by Arduino IO port ESP-12F can work as slave mode for arduino, or program independently. ADC and ADC external voltage port lead out. On board PROG programmable button, and ESP reset button. Demo code inlcudes manipulating AT commands to transiceive data from web, find in the wiki documentaion link below. Can be used independently, can be connected to a standard serial communication FTDI Lora Module SX1278/76: Reserved but not place module. D10 default used for lora chip select pin. D5-D7 can connect via jumper to D1, D2, D5 lora DIO pins. D2 default used for lora IRQ DIO0 pin. Antenna not connected default, support pin, ipex, or sma type connector, suit your needs. All lead out DIO D0 ~ D5 pins on side. Addon: Extra DH11 socket, with 10K pull-up data pin. Packaging: Only include the main board with esp-12F as red board. Not include any pin headers, lora module, antenna. Arduino pin header please buy alone here. the last image of the green board indicates the final soldered state only. Documentation please see on this page.
Arduino LA66 LoRaWAN Shield Dragino
The Relay shield is capable of controlling 2 relays. The max switching power could be 10A/250VAC or 10A/30VDC. It could be directly controlled by
Wireless NRF24 Controlled Relays Arduino Shield
LoRa SX1278 & ESP8266 Transmitter Receiver with DHT11 Sensor
GPS:, Use GPS module Ublox Neo-7M, or NEO-6M or ATGM332 compatible GPS module. All have the same performace., Fast and high speed locating., By
GPS SD RF Lora Shield for Raspberry Pi R2 (w/o Lora Module)
LoRa Shield for Arduino Faststream Technologies
This TTGO Board Combines ESP32, LoRa Radio, and OLED Display for
Portenta Vision Shield - LoRa® — Arduino Online Shop
LORA WIFI RF Arduino Shield, ESP8266 SX1278 - ElectroDragon
Using FSK / GFKS technology and LoRa (remote) spread spectrum technology. Super anti-jamming (channel rejection ratio: 56db). ISM multi-band, no need
Comimark 2Pcs LoRa SX1278 Long Range RF Wireless Power Mental Module SX1276 5Km for Arduino
The Internet of Things with ESP32
LoRa Radio Node v2.0 Based on Sx1278 LoRa 433Mhz 2.4G RFM98 for
The Relay shield is capable of controlling 2 relays. The max switching power could be 10A/250VAC or 10A/30VDC. It could be directly controlled by
Wireless NRF24 Controlled Relays Arduino Shield
LORA WIFI RF Arduino Shield, ESP8266 SX1278 - ElectroDragon
ESP8266 ESP-12F Wifi development board, Breadboard compatible, Pin headers are included but needed to be soldered by yourself, Left and right side
D1 Mini WIFI Dev Board, ESP8266 ESP-12F
Gowoops SX1278 LoRa Radio Wireless 433Mhz 410~441MHz
Recommandé pour vous
- Arduino Wi-Fi Shield - DEV-11287 - SparkFun Electronics14 Jul 2023
- Arduino MKR WiFi 1010 [ABX00023]14 Jul 2023
- Arduino Uno Compatible + WiFi14 Jul 2023
- Cheap Arduino clones with ESP8266 wifi, by Tim Gerla14 Jul 2023
- Wifi Shield14 Jul 2023
- Hardware Basics of Arduino UNO WiFi Rev2 - Iotguider14 Jul 2023
- WiFi Module - ESP8266 (4MB Flash) - WRL-17146 - SparkFun Electronics14 Jul 2023
- Connect an Arduino UNO WIFI to your network - TrojanC14 Jul 2023
- Dual-core 32-bit Arm MCU Arduino GIGA R1 WiFi Development Board for IoT Solution - DFRobot14 Jul 2023
- WiFi Shield14 Jul 2023
Tu pourrais aussi aimer
- Caméra De Voiture Wifi 5 720p Hd, Vue Latérale Gauche Et Droite14 Jul 2023
- Maltesers Small Box 110g / Maltise / Chocolate14 Jul 2023
- Peinture glycéro blanc mat - pot 10l14 Jul 2023
- Canon 057H Toner Cartridge With Chip - 314 Jul 2023
- Samsung Galaxy Tab A8 Review: Almost Budget Brilliance - Tech Advisor14 Jul 2023
- 36oz Yetys Water Bottle, Y Stainless Steel Waters Bottle, Travel Cup Coffee Mug, gourde sublimation, garrafa termica thermos - AliExpress14 Jul 2023
- Grey Goose Vodka 1l, Perth Airport Digital Marketplace14 Jul 2023
- UFC Co-ord Graphic Joggers14 Jul 2023
- Miroir salle de bain 40x60cm avec éclairage – Go LED - AURLANE14 Jul 2023
- Soekodu Mini Imprimante, Imprimante de Poche Petite Imprimante Portable avec 8 Rouleaux de Papier et 5 Rouleaux Autocollants Imprimante Photo sans Fil14 Jul 2023